Spare part list
Floor watering system
Copyright © 2018 Lubing System - All rights reserved
21
1. Adjustment of the ball valve in the riser permits readjustment of the water volume. The water column is
properly adjusted when a height of 22 – 25 cm (8 10 in) (measured from above the
spraying tube) is reached in paper pads and one of 15 18 cm (6-7 in) (measured
from above the spraying tube) in plastic pads.
4.3 Operation of the system
Durability of the pad depends on the respective water quality of the location. The Pad-Climate-System circulates and
evaporates water in a circle. This causes continuous in-crease of the mineral and foreign substance concentration
of the water. In order to keep the mineral content within the desired level, a share of up to 10% of the circulated
water can be continually released by the drain device. The mineral occurrence on the pads generally should be
observed. The higher this is the more water should be exchanged continually (on this, also see chapter 3.7).
Algae growth and water bacteria in the pads must be checked. The pads are treated with an anti-fungal additive
that will not, however, prevent algae growth. Treat the water with calcium hypo chlorinate as is used for swimming
baths. Tablet forms of such algaecides are the most economically efficient form and best for slow release. Keep the
water at 1 ppm (parts per million) of chlorine for recirculation. If you can smell the chlorine, too much was added.
When algae are growing, tablets must be added. The pH-value and chlorine content should be reviewed every
week.
The longevity of the pads and the pad frame depends on proper maintenance.
Clean the pump filter at least once per week or more often if there are any foreign sub-stances in the water system.
Clean the spraying tube at least once per month. This can be simplified by opening the two closure caps while the
pump is running and water can flow through.
Always regulate your ventilation system so that the pad system is turned off while all fans are still running. This will
dry the pads and kill all algae spores. Do not keep the pads wet-ted around the clock. This will soften the pads.
Check the pads for dry spots while the pad system is in operation. If dry spots occur, re-move the pad cover and
check the holes in the tube. Clean all clogged holes with a wire until enough water flows from each hole.
The pads are more efficient when they have just enough water
to stay wet. Flood-like sprinkling will soften the pad and render it
inefficient.
Empty and clean the water trough as often as necessary to remove
dirt or waste so that the water can circulate freely.
WARNING
The pH-value of the recirculated water must be kept be-tween 6 and 9. A pH-value of 7 is neural. A pH-
value above 9 or below 6 will drastically reduce the pad’s ser-vice life.
DANGER!
Please do not put too much water on the pads.
PERICOLO!
The pump must be drained in time if there is a danger of
frost.
It is drained through the closure screw. Also empty any
lines in danger of frost.
The pump must be disconnected from the mains for any
maintenance work.
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
