Lovi HL-0893, Manual

Page: 2 / 45

2 3
• When sterilising other accessories used for babies or nursing mothers, place the items in the basket in such a
way as to leave enough room for the hot vapour to reach them easily.
• DO NOT place electrical appliances or components containing metal inside the steriliser due to the risk of
damage.
• DO NOT use bleaches or chemical solutions, or disinfectant tablets in the steriliser or for the products that will
be sterilised in it.
• During operation, there is hot water and hot vapour in the steriliser.
• Take special care when lifting the device with hot liquids.
• DO NOT touch the body of the device when it is switched on.
• NEVER cover vent holes in the steriliser’s lid.
• NEVER put any items on the steriliser’s lid.
• NEVER open the steriliser whilst in use.
• Remember that when switched on, the product contains boiling water. Beware of escaping steam from the
vent holes in the lid.
• After each use, after the device has cooled down, pour away any remaining water. Do not store the device filled
with water.
• ALWAYS allow the device, water, and vapour to cool for at least 3 minutes before opening the lid.
• Take care when lifting the steriliser lid after use to avoid scalding. It is recommended to use kitchen gloves that
protect hands against high temperatures.
• WAIT until the device cools down before removing or inserting new items.
• To stop the steriliser during the cycle, press the STOP button, and then disconnect it from the power socket.
• NOTE! Use pre-boiled or demineralised water, as it prevents limescale build-up on the heating plate. Avoid
using mineral water as it significantly increases the build-up of scale on the heater. The presence of limescale
on the heating plate is not subject to the warranty.
• Maintenance of the steriliser, other than cleaning or limescale removing, is not required.
• Failure to follow the correct descaling instructions can cause irreparable damage to the product.
• DO NOT use any caustic substances or chemicals for cleaning.
• For cleaning the steriliser use only clean water, to prevent stains forming.
• This product is not a toy. Use and store the device and all its parts out of the reach of children.
• Do not disassemble the product.
• It is forbidden to redesign and modify the product. Any action contrary to this guideline cancels the EC
declaration of conformity.
• If you have any doubts about the safety of the product, please contact with distributor or manufacturer.
THE INSTRUCTIONS ABOVE MUST BE STRICTLY FOLLOWED.
THE MANUFACTURER IS NOT LIABLE FOR DAMAGES RESULTING FROM THE MISUSE OF THE DEVICE.
DEVICE SPECIFICATION
Model Voltage Power
HL-0893 220V - 240V / 50Hz Steriliser 600W
Dryer 180W
INSTRUCTION MANUAL
Before using the steriliser, please ensure that you read these instructions thoroughly. Keep the instructions
manual as it contains important information.
Extremely convenient to use and effective LOVI Electric Steam Sterilizer with Dryer will ensure maximum hygiene
within 10 minutes. With its help, you will sterilise up to 4 different size bottles.
PRODUCT COMPONENTS
A - lid handle
B - transparent lid with vent holes
C - accessories tray
D - main container for sterilization/drying
E - base with a heating plate and power cable
F - heating plate
G - filter protecting against dirt in the device
H - DISPLAY
BEFORE THE FIRST USE
• Unpack the product from the foil packaging. Plastic bags can be dangerous. Keep the packaging out of reach
of infants and small children to prevent the risk of suffocation.
• Before first use, thoroughly clean the inside of the device and all its components with warm water and a
mild cleaning agent (do not immerse the device body in water!) and wipe dry with a cloth. Perform the first
sterilisation on the empty device to sterilise the inside of the steriliser.
• Pour 100 ml of water onto the heating plate (F) (it is recommended to use boiled water which prevents the
formation of limescale on the elements of the device).
• Insert the main container (D) into the base (E) and then place the accessories tray inside and put the lid (B) on.
• Connect the device to the mains supply. You will hear a beep sound and the display will show --. Press the
sterilization switch button . The display will count down to 10 minutes.
• When the sterilisation process is finished, you will hear a beep sound three times. The counter will switch off.
• Wait for the device to cool down. It should cool down for at least 3 minutes. Then unplug the power cord from
the mains and remove the lid (B).
• Remove the tray from the main container. Wipe all parts of the steriliser with a dry cloth to prevent a build-up
of limescale or residue.
INSTRUCTIONS FOR USE - STERILISATION MODE
• Important!
Before beginning the sterilisation, wash all the elements according to their instructions, and rinse
thoroughly.
• Separate all components: teats from bottles, caps, sealing discs, etc.
• Pour 100 ml of water onto the heating plate (F) (it is recommended to use boiled water which prevents the
formation of limescale on the elements of the device).
• Place 4 bottles on the base of the main container (D) upside down on specially designed locators. You can
place the accessories tray (C) between the bottles in the centre of the device, together with accessories for
sterilisation. If you will not assemble the accessories tray, you can place extra 1-2 bottles. When placing items
in the device, make sure that the steam can circulate effectively between all items. Place the lid (B) onto the
steriliser.
• Connect the device to the mains supply. You will hear a beep sound and the display will show --. Press the
sterilization switch button . The display will count down to 10 minutes.
• NEVER lift the lid while the device is operating. Remember that during operation, there is hot water and
hot vapour in the steriliser.
• After the process is completed, the device will stop working. You will hear a beep sound three times.
• Wait for the device to cool down. It should cool down for at least 3 minutes. Then unplug the power cord from
the mains and remove the lid (B).
• Remove the tray, bottles, and accessories from the main container. Wipe all parts of the steriliser with a dry
cloth to prevent a build-up of limescale or residue.
GB