manualshive.com logo in svg

LM-Dental LM-ProPower CombiLED, User Manual

Share
Download
LM-Dental LM-ProPower CombiLED User Manual Download Page 32

Cleaning and maintenance

32

Autoclave in steam at 134°C (max 135°C) for minimum 3 minutes 

Scaler tips

Polisher nozzle

Torque wrench

LM-ErgoGrip Focus LED

LM-ProPower Scaler handpiece

7.4.  Recommended cleaning procedure

Beginning of the day

Run the automatic cleaning cycle with clean water for both scaler and polisher. See instructions chapter “7.2. 
Automatic cleaning function for the scaler and polisher” on page 30.

After each treatment

•  To prevent clogging, air purge the polisher handpiece after each treatment. See instructions “6.4. Air 

purge quick cleaning function” on page 27.

•  Run the automatic cleaning cycle with clean water for both the scaler and polisher. See instructions “7.2. 

Automatic cleaning function for the scaler and polisher” on page 30.

•  Clean off the cover, control panel, handpieces and the hoses with a soft cloth. Use a surface disinfectant 

suitable for hard plastics.

•  Clean the nozzle in an ultrasonic bath (40-50°C), for minimum 3 minutes, before cleaning/sterilization. If 

ultrasonic cleaning is not possible, flush the nozzle with warm water.

•  Clean the ErgoGrip, the tip, the nozzle and possibly the scaler handpiece and autoclave according to the 

clinic’s routines.

Summary of Contents for LM-ProPower CombiLED













































Reviews:

No comments

Brands by name

Popular brands

Load more brands