manualshive.com logo in svg

LM-Dental LM-ProPower CombiLED, User Manual

Share
Download
LM-Dental LM-ProPower CombiLED User Manual Download Page 26

Operating instructions AirLED Polisher 

26

AirLED Polisher

A

1.  Unscrew the powder container from the cap and fill 

the powder container with LM-ProPower powder 
until MAX (A).  
NOTE: With LM-Glycine powder fill the powder 
container only half of the maximum to prevent too 
much powder consumption and dispersion. 

2.  Screw the container back in to the cap.
3.  Connect the powder container cap to the 

connectors on the right side of the unit (B). 

4.  Bottle version: Connect the medicament bottle to 

the unit.

5.  Carefully move the LM-ErgoGrip onto the polisher 

handpiece (C). 

6.  Screw the polisher nozzle clockwise into the 

handpiece until you feel a stop (D). 

7.  Press the key identified P on the control panel (E) to 

Set the polisher ON. The blue polisher indicator lamp 
illuminates.

8.  The indicators adjacent to the working modes 

keys are flashing to remind that you must select 
a working mode. If some blue indicators are 
flashing alternatively, make sure that the polisher is 
connected. If the problem stays, refer to the trouble 
shooting section. Choose working mode 2 or 3 
by pressing the related working mode key on the 
keyboard. 

9.  Adjust water flow for optimal performance.

• Point the handpiece to the cuspidor and above the 

bowl. Push the foot switch to activate the polisher 
and adjust the water flow on the powder container 
(F).

• Hold the polisher nozzle approximately 1 cm (0,4 

in.) down right from the bottom of the bowl and 
press the foot control to activate the polisher.

• Slowly reduce the water flow until the powder starts to 

collect on the surface as a white spot.

• Increase the water flow until the spot just 

disappears. The air polisher is now balanced for 
optimum performance.

B

C

D

E

F

Summary of Contents for LM-ProPower CombiLED













































Reviews:

No comments

Brands by name

Popular brands

Load more brands