manualshive.com logo in svg

LM-Dental LM-ProPower CombiLED, User Manual

Share
Download
LM-Dental LM-ProPower CombiLED User Manual Download Page 17

Taking CombiLED in to use

17

4.  TAKING COMBILED IN TO USE

NOTICE!

The product should not be used adjacent to or stacked with other equipment. 

If adjacent or stacked use is necessary, the product must be observed to verify 

correct operation in the configuration in which it will be used.  

NOTICE!

Special skills required. Consult an approved technician to connect the unit to 

the air and water supply.

NOTICE!

Do not put the unit on or adjacent to a heat source. Excessive heat can damage 

the electronics. 

NOTICE!

Product is not suitable for use in the presence of flammable gases.

4.1.  How to install the unit

• Put the unit horizontally with the handpieces in the 

holders and the hose hanging free.

• Put the unit where air is free to circulate on all 

sides and below it. Do not put the unit on a wall or 
adjacent to heat source.

• Do not put the unit in the immediate vicinity of 

sources of electromagnetic radiation, for example 
an electro surgery equipment.

• Connect the foot control cable to the foot control 

and at rear side of the unit.

• Install the scaler tubing in the grove below the unit, 

as in picture.

Summary of Contents for LM-ProPower CombiLED













































Reviews:

No comments

Brands by name

Popular brands

Load more brands