manualshive.com logo in svg

LM-Dental LM-ProPower CombiLED, User Manual

Share
Download
LM-Dental LM-ProPower CombiLED User Manual Download Page 27

Operating instructions AirLED Polisher 

27

6.2.  Foot control functions for Polisher

5

4

3

1

2

1 OFF position
2 ON position
3 Diagnostic function, set LED light ON or OFF  

by a single-click on the pedal

4 Water Jet position
5 Polisher ON (Power controlled on control panel)

6.3.  Power and working modes for Polisher

Polishing power 

The user controls the polishing power from the control panel. Working modes 2 and 3 are possible working 
modes for the polisher. 

B

A

•  Working mode 2 is approximately 60% of 

polishing power (A). 

•  Working mode 3 is approximately 100% of 

polishing power (B). 

Choose correct working mode from the control panel.

•  When working with a subgingival nozzle, 

always use working mode 2 (A).

Water-Jet cleaning 

The Water-Jet cleaning mode is cleaning without powder. Select the Water-Jet cleaning mode with the foot 
control pressed down in the leftmost position. Only water and air comes out from the nozzle. User can also 
select the Water-Jet cleaning mode by pressing “P” key three times on the control panel.

Air-Blow mode 

Press one time of the “P” key to activate the Air-blow mode for cleaning with just air.  
When you press the “P” key again and again, it will toggle between normal polishing-, Air-blow - and Water-Jet 
mode. 

6.4.  Air purge quick cleaning function 

With the polisher mode active, a press on the “C” key will air purge the handpiece for a few seconds. Air 
purge the handpiece after each treatment to prevent clogging. If the air purge are not performed the indicator 
adjacent to the “C” key will flash as an remainder. Running air purge resets the remind function.

Summary of Contents for LM-ProPower CombiLED













































Reviews:

No comments

Brands by name

Popular brands

Load more brands