manualshive.com logo in svg

LM-Dental LM-ProPower CombiLED, User Manual

Share
Download
LM-Dental LM-ProPower CombiLED User Manual Download Page 22

Operating instructions UltraLED Scaler

22

5.2.  Foot control functions for Scaler

5

7

6

4

3

1

2

1

OFF position

2

ON position

3

Diagnostic function, set LED light ON or OFF by  
a single-click on the pedal

4

Irrigation position

5

Zero power position

6

Maximum power position

7

Power regulation

5.3.  Power and working modes for Scaler 

Scaling power 

The power is controlled with the foot control from 0 to 100% in each working mode. See the recommended 
working mode that is identified on the tip. Press the related working mode key on the keyboard. 

Dry mode for scaling 

Press one time of the “S” key to activate the dry mode for scaling without water/medicament. 

Irrigation mode 

Press two times of the “S” key to activate the irrigation mode. You can also activate the irrigation mode in the 
scaling mode by pressing down the foot control in the leftmost position. 

When you press the “S” key again and again, it will toggle between normal scaling, dry and irrigation mode.  

Summary of Contents for LM-ProPower CombiLED













































Reviews:

No comments

Brands by name

Popular brands

Load more brands