background image

 

16 

  POWER 

  POWER key: 
  A.  Press  to  pop-up  "light"  /  "background  color"  shortcut  menu,  and  then  setting 
through four-in-one multi-function key; 
  B. Press the power button of 2S device. The device is powered on when pressing the 

POWER  button.  When  the  device  is  running,  press  the  POWER  key,  the  screen  will 
display  the  message  "Power  off  Countdown"  over  the  countdown,  the  host 
immediately shut down and then release button; otherwise release after the operation is 
disabled. 

6. The Menu System 

All multi-level or equivalent menu in the menu when pops up, to select through up / down key 
of  "Four-in-one  multi-function  key";  and  then  adjust  through  left  /  right  key.  Short  press  and 
long-keep press for Left / Right adjustment. Short press to make step size adjustment effective 
immediately; long-keep press to make value adjustment effective after release.   

6-1.

 

Main Menu:   

1.

 

Sensitivity  :1-20  levels,  short  press  to  make  step  size 
adjustment  effective  immediately;  long-keep  press  to 
make  step  size  adjustment  effective  after  release.  This 
feature  is  to  adjust  the  level  and  width  of  sonar  colors. 
The default value is "10". 

2.    Upper Range: 

  A.  “m”  as  unit:  0  to  397  levels,  step  size  is  1,  and  the 

minimum interval with lower range is 3m; 

  B.  “feet”  as  unit:  0  to  1302  levels,  step  size  is  1,  and  the 

minimum interval with lower range is 10 feet; 

  C.  “fathom”  as  unit:  0-216  levels,  step  size  is  1,  and  the  minimum  interval  with  lower 

range is 2 fathoms;   

Short press to make step size adjustment effective immediately; long-keep press to make 

step  size  adjustment  effective  after  release.  This  feature  shows  location  on  the  screen. 
The  depth  of  upper  range  is  less  than  lower  range,  and  different  depth  under  different 
units.  The  value  of  upper  range  is  fixed  to  0  when  in  the  window  of  single  tranducer 
plus zoom, and default as 0 when in another window. Menu will pop-up through either 
main menu or shortcut key.   

3.    Lower Range: 

  A.  “m”  as  unit:  3  to  400  levels,  step  size  is  1,  and  the  minimum  interval  with  lower 

range is 3m; 

  B. “feet” as unit: 10 to 1312 levels, step size is 1, and the minimum interval with lower 

range is 10 feet; 

  C. “fathom” as unit: 2-218 levels, step size is 1, and the minimum interval with lower 

range is 2 fathoms; 

Short  press  to  make  step  size  adjustment  effective  immediately;  long-keep  press  to 

make  step  size  adjustment  effective  after  release.  This  feature  shows  location  on  the 
screen.  The  depth  of  upper  range  is  less  than  lower  range,  and  different  depth  value 

Summary of Contents for LCD Fish/Depth Finder
























Reviews: