background image

 

4. Display Window

 

4-1. Title Screen 

Turn on your device F403S by pressing the POWER key. The 
title  screen  is  display  until  the  F403S  begins  operation.  The 
device  will  begin  Normal  or  Simulator  operation,  depending 
on your choice.   
Press MENU to begin Simulator operation. The simulator data 
is available under this mode; however the recording function 
is  unavailable  under  simulator  mode.  Otherwise  it  will  enter 
normal  operating  mode.  In  normal  mode  there,  enter  the  last 
visit of the view interface. 
 

4-2. Sonar View 

1. Sonar Color Bar: Color spectrum indicating low to high sonar 
intensity  returns,  where  red  indicates  high  intensity  and  white 
indicates low intensity, default value: standard. 
2. Real Time Sonar Window: Display the  real time sample data, 
the display mode can be changed, default value: waveforms. 
3.

 

Water Surface Noise: The noise waveforms from Sonar returns. 

4.

 

Sonar Return: First sonar return, it indicates depth of the water 

at present. 
5.

 

Second Sonar Return: When the sonar signal bounces between 

the bottom and the surface of the water and back again. Use the 
appearance  of  the  second  return  to  determine  bottom  hardness. 
Hard  bottoms  will  show  a  strong  second  return,  while  soft 
bottoms will show a very weak one or none at all. 
6.

 

Third  Sonar  Return:  When  the  sonar  signal  bounces  between 

the bottom and the surface of the water and back again. 
7.

 

Window 1: Water depth, can set depth alarm, default value: off. 

8.

 

Window 2: Input Voltage, can set low battery alarm, default value: off. 

9.

 

Window  3:  The  temperature  display,  the  current  location  of  underwater  transducer 

temperature, the current water temperature alarm can be set; set off according to user needs 
or display, default value: off. 

10.

 

On the range: the range of display settings, you can manually set, default value: 0 

11.

 

The following range: Display settings under the scope, you can manually set, default value: 

auto. 

12.

 

Depth contours: with three lines to the screen is divided into several equal portions, you can 

also turn off the menu, default value: off 

13.

 

Background  color:  blue,  white,  black.  Different  background  colors,  font  colors  displayed 

are not the same, default value: blue. 

Summary of Contents for LCD Fish/Depth Finder
























Reviews: