Lighthouse Worldwide Solutions ApexR02 Operating Manual Download Page 23 | Manualshive

Page: 23 / 84

background image

00

248083447-1 Rev 1

3-1

3

Get Started

Unpacking
and Initial
Inspection

The instrument is thoroughly inspected and tested at the factory and is
ready for use upon receipt.

It is presumed that when the instrument was received, its shipping
carton was inspected for damage. If the carton was damaged, the carrier
was notified and the carton was saved for carrier inspection. The
instrument and other components were then removed from their
packing materials and inspected for broken parts, scratches, dents, or
other damage. Any damage was immediately reported to Lighthouse.
Damaged cartons may be replaced by calling Lighthouse Sales. Keep
an undamaged carton for reshipment of the instrument for its annual
factory calibration.

Identify the

Apex

Remote

Model

The

Apex

Remote

is available in two models:

Serial

and

PoE

. The

Apex

Remote

Serial

re24VDC to be supplied through its

RJ45 connector. The

Apex

Remote

PoE

requires a customer-

supplied PoE network switch or an optional 24VDC Power Supply
using the power connector shipped with the

Apex

Remote

and a Cat6

cable to a non-PoE switch. All models can be equipped at the factory
with an optional display.

Compare
Contents

Compare the contents with the pack slip / invoice / parts list. Report

immediately any missing or wrong parts to Lighthouse Support at 1-

800-945-5905 in the USA or 1-541-770-5905 outside of USA.

Configuration
Kit

Each order is shipped with a

Configuration Kit

, which includes the

SmartPort

cable, software CD and a 24VDC Power Supply.

To properly use the kit, the software on the CD must be installed on a
computer that will act as a configuration station. Running the

LWS

Instrument Setup Tool

software will install the FTDI USB drivers and

the

Instrument Setup Tool

software required to communicate with the

instrument through the

SmartPort

cable. This cable and the software

are required to set up all

Apex

Remote

instruments for use.

«
...
21
22
23
24
25
...
»

Summary of Contents for ApexR02





















































































Reviews:

No comments

Related manuals for ApexR02

Mentor Visual iQ

Brand: GE Pages: 2

Brand: Igema Pages: 30

Brand: z-laser Pages: 62

Brand: Teac Pages: 148

Brand: IFM Pages: 25

Brand: Campbell Pages: 16

Surface Scatter 7 sc

Brand: Hach Pages: 6

Brand: Hach Pages: 118

Brand: Hach Pages: 388

Orbisphere 51 Series

Brand: Hach Pages: 118

ORBISPHERE 3650 Atex

Brand: Hach Pages: 51

Brand: Hach Pages: 72

POLYMETRON 8362

Brand: Hach Pages: 78

Pocket Colorimeter II

Brand: HACH LANGE Pages: 146

Brand: Hach Pages: 146

Brand: Hach Pages: 36

PHOSPHAX indoor sc

Brand: Hach Pages: 104

Lange ORBISPHERE 3100

Brand: Hach Pages: 384

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands