Lighthouse Worldwide Solutions ApexR02 Operating Manual Download Page 54

Page: 54 / 84

Lighthouse ApexRemote Operating Manual

7-4

248083447-1 Rev 1

7. Attach the

Apex

Remote

to the

SmartBracket

by slipping it over

the mounting screws provided and sliding it downward on the
Bracket. Tighten the two screws. See Figure 7-5.

Figure 7-5 Attach

Apex

Remote

SmartBracket

8. The

Apex

Remote

is now ready for connection to the network.

Installing

Apex

Remote

without

SmartBracket

1. Using a bubble level to ensure

Apex

Remote

is level, place the

Apex

Remote

against the vertical surface upon which it will be

mounted.

2. Mark the center of each mounting tab’s larger hole then remove the

Apex

Remote

from the surface and drill pilot holes for the

mounting hardware.

3. Install the mounting hardware then the

Apex

Remote

, snugging

the instrument to prevent wobble or movement while it is in use.

4. Install the necessary cable and vacuum tubing.

5. The instrument is ready for connecting and integrating into the

instrumentation network.

Summary of Contents for ApexR02





















































































Search results

Summary of Contents for ApexR02

Reviews:

Related manuals for ApexR02

Brands by name

Popular brands

Lighthouse Worldwide Solutions ApexR02, Operating Manual

Search results

Summary of Contents for ApexR02

Reviews:

Related manuals for ApexR02

Brands by name

Popular brands