Life Fitness Lifecycle 9500RHR Series Service Manual Download Page 10

Page: 10 / 105

Lifecycle 9500RHR Series Exercise Bikes

TROUBLESHOOTING GUIDE

Symptom: Display Console LEDs Remain Illuminated

Symptom

Probable Cause

Corrective Action

Display Console LEDs do
not extinguish in timely
manner at the end of a
workout , when the CLEAR
key is pressed, or when the
pedaling stops.

Loose wire connections

Disconnect then reconnect the connections.

Worn or damaged harnesses

Inspect wire harnesses. Replace worn or
damaged harnesses.

Malfunctioning Alternator
Control Board

Test with substitute Alternator Control Board.
Replace defective board.

Malfunctioning Display Console

Inspect for damage or depression at START
key. Test with substitute Display Console.
Replace malfunctioning Display Console.

For Assistance Contact
Life Fitness Customer Support Services
Teleph.: 847.451.0036 or 800.351.3737
Telefacs.: 847.288.3702 or 800.216.8893

Summary of Contents for Lifecycle 9500RHR Series










































































































Search results

Summary of Contents for Lifecycle 9500RHR Series

Reviews:

Related manuals for Lifecycle 9500RHR Series

Brands by name

Popular brands

Life Fitness Lifecycle 9500RHR Series, Service Manual

Search results

Summary of Contents for Lifecycle 9500RHR Series

Reviews:

Related manuals for Lifecycle 9500RHR Series

Brands by name

Popular brands