Life Fitness Lifecycle 9500RHR Series Service Manual Download Page 20

Page: 20 / 105

Lifecycle 9500RHR Series Exercise Bikes

TROUBLESHOOTING GUIDE

Symptom: Battery Over-Heating

Symptom

Probable Cause

Corrective Action

Battery over-heating during
exercise program.

Battery Wires incorrectly
connected

Inspect connections: red wire to positive (+)
lead; black wire to negative (-) lead.

Worn Battery Wires

Inspect Wires. Replace Wires or harness.

Battery leads grounding upon
frame

Inspect leads. Replace battery.

Malfunctioning Display Console

Test with substitute Display Console. Replace
malfunctioning Display Console.

Malfunctioning Alternator
Control Board

Test with substitute Alternator Control Board.
Replace defective board.

For Assistance Contact
Life Fitness Customer Support Services
Teleph.: 847.451.0036 or 800.351.3737
Telefacs.: 847.288.3702 or 800.216.8893

Summary of Contents for Lifecycle 9500RHR Series










































































































Search results

Summary of Contents for Lifecycle 9500RHR Series

Reviews:

Related manuals for Lifecycle 9500RHR Series

Brands by name

Popular brands

Life Fitness Lifecycle 9500RHR Series, Service Manual

Search results

Summary of Contents for Lifecycle 9500RHR Series

Reviews:

Related manuals for Lifecycle 9500RHR Series

Brands by name

Popular brands