Life Fitness Lifecycle 9500RHR Series Service Manual Download Page 8

Page: 8 / 105

Lifecycle 9500RHR Series Exercise Bikes

TROUBLESHOOTING GUIDE

Symptom: Display Console Initializes Then Fails

Symptom

Probable Cause

Corrective Action

Display Console initializes
then fails

Loose wire connections

Disconnect then secure connections.

Worn or damaged wire
harnesses

Inspect wire harnesses. Replace worn or
damaged harness.

Malfunctioning Display Console

Test with substitute Display Console. Replace
malfunctioning Display Console.

Malfunctioning Alternator
Control Board

Test with substitute Alternator Control Board.
Replace malfunctioning board.

Malfunctioning Alternator

Test Alternator output or, test with substitute
Alternator. Replace malfunctioning Alternator.
Refer to Alternator Voltage Test.

For Assistance Contact
Life Fitness Customer Support Services
Teleph.: 847.451.0036 or 800.351.3737
Telefacs.: 847.288.3702 or 800.216.8893

Summary of Contents for Lifecycle 9500RHR Series










































































































Search results

Summary of Contents for Lifecycle 9500RHR Series

Reviews:

Related manuals for Lifecycle 9500RHR Series

Brands by name

Popular brands

Life Fitness Lifecycle 9500RHR Series, Service Manual

Search results

Summary of Contents for Lifecycle 9500RHR Series

Reviews:

Related manuals for Lifecycle 9500RHR Series

Brands by name

Popular brands