50
51
6. Assemble the MATING BRACKET (q) to the back of the
ATTACHABLE TV (cc) with four SCREWS (r) and four
steel WASHERS (s).
7.
Assemble the ATTACHABLE TV to the TV MOUNTING
BRACKET. Insert one HEX BOLT (t) and WASHER (u)
through both parts that make up the hinged bracket.
Partially tighten both brackets with one LOCK NUT (v).
Adjust the TV position so that the TV face is
perpendicular to the floor. Insert two screws (w) to lock
the bracket position. Fasten the hinged bracket
securely.
8. Insert one end of the AUDIO / S-VIDEO / I-R REMOTE
CONTROL CABLE ASSEMBLY into the CONSOLE
CONNECTOR.
9. Reattach the console to the console support bracket
with the four previously removed screws in Step 2.
Tighten the screws to 6-8 in-lbs.
Connect the COAXIAL CABLE, POWER CORD, and
AUDIO / S-VIDEO / I-R REMOTE CONTROL CABLE
ASSEMBLY to the rear of the ATTACHABLE TV.
See the
Media Connections
pages in this manual for detailed information.
10. Re-insert the previously removed square END CAP (a) into the top of the TV MOUNTING BRACKET.
11. Secure the POWER ADAPTER (x) to the FRONT STABILIZER (y) using two CABLE TIES (z) as shown. Be sure the
CABLE TIES are pulled tight and trim the excess CABLE TIES. Connect the screw-type connector of the POWER
CORD (aa) to the underside receptacle. Bundle excess power cord and store under the unit. Connect the COAXIAL
CABLE (bb) to the broadcast supply receptacle in similar fashion.
12. Connect the POWER SUPPLY CORD to the POWER ADAPTER (x).
13. Continue with the remainder of assembly as instructed in the Assembly Instructions. Plug the POWER SUPPLY
CORD into an electrical outlet upon completion.
x
y
z
aa
bb
s
r
t
w
u
v
q
cc
Model: CLSR (Integrity Series)
Tools Required:
Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters
Note:
The following Assembly Instructions show the console attached prior to ATTACHABLE TV installation. Follow all
appropriate steps when the console is not mounted.
1. Remove the square END CAP (a) and two PLASTIC PLUGS
(b) located behind the console on the MAIN CONSOLE
SUPPORT TUBE (c).
2. Remove the four SCREWS (d) that are used to fasten the
console. Carefully set the console aside, securing it so that it
does not fall.
3. Locate the TV MOUNTING BRACKET (e). Unwrap the POWER
SUPPLY CORD (cc) and COAXIAL CABLE (dd) located within
the CONSOLE SUPPORT BRACKET TUBE (c). Route these
cables through the opening of the TV MOUNTING BRACKET
(e).
Locate the AUDIO / VIDEO / I-R REMOTE CONTROL
CABLE ASSEMBLY (f). Route this cable assembly through the
TV MOUNTING BRACKET(e) with the 2-connector end
coming out of the opening of the TV MOUNTING BRACKET.
4. Insert the TV MOUNTING BRACKET into the CONSOLE
SUPPORT TUBE and fasten with three SCREWS (h) and three
WASHERS (i).
CAUTION:
Do not pinch any cables when inserting the TV MOUNTING BRACKET into the CONSOLE SUPPORT TUBE.
5. Assemble the HINGED BRACKET (j) to the TV MOUNTING BRACKET with the following provided hardware:
k.
screw
l.
steel
washer
m.
nylon plastic washer
n.
nylon plastic shoulder washer
o.
steel
washer
p.
nut
a
b
d
c
h
i
j
p
o
k
l
m
n
g
f
f
dd
cc
e
Summary of Contents for ATV15-XXXA-02
Page 1: ...1008767 0001 AA 15 ATTACHABLE TV ASSEMBLY INSTRUCTIONS ...
Page 2: ......
