48
49
11. Tilt the DISPLAY CONSOLE back into place. Replace the REAR
CONSOLE COVER (9) and secure it using the previously removed
four SCREWS (8). Tighten the screws securely. (8-10 ft. lbs.). Do not
overtighten the screws.
12. With the remaining TV BRACKET (20) oriented as shown, install it to
the back of the ATTACHABLE TV (21) using four SCREWS (22) and
WASHERS (23). Tighten the screws securely. (8-10 ft. lbs.)
Note:
Be sure the side holes of the TV BRACKET are oriented as
shown.
13. Position the TV BRACKETS (4 & 20) together and secure them
using one BOLT (24), WASHER (25) and NUT (26). Leave the
bolt and nut loose at this time.
Note:
Be sure the PIVOT POST of the TV BRACKET engages
onto
TV BRACKET.
14. Connect all cables to their corresponding jacks located on
the bottom of the ATTACHABLE TV. See the
Media
Connections
pages in this manual for detailed information.
Feed any excess media cable into the MAIN BRACKET (5).
15. Align the lowest side holes on the TV BRACKETS (4 & 20). Secure the
TV BRACKET into proper position using one SCREW (27) on each side.
16. Plug in and power on the TV. Refer to the
ATTACHABLE TV
Operation
Manual for proper TV setup.
For Achieve Console Units Only:
a. Remove the two SCREWS (A) and WASHERS (B) securing the
BOTTOM INSERT (C). Remove the BOTTOM INSERT. Do not
discard the SCREWS and WASHERS.
b. Locate the REMOTE CONTROL (D) and REMOTE BRACKET (E).
Feed the REMOTE CABLE (F) through the large access hole
in the REMOTE BRACKET (E). With the REMOTE CONTROL (D)
and REMOTE BRACKET (E) oriented as shown, secure them
together using one SCREW (G). Tighten the screw securely.
c. Carefully feed the REMOTE CABLE (F) through the opening in
the bottom of the CONSOLE (H) and through the back of the
console. Position the REMOTE BRACKET (E) into position
replacing the BOTTOM INSERT (C). Secure the REMOTE
BRACKET using the previously removed SCREWS (A) and
WASHERS (B).
H
16
D
A
A
C
B
16
E
F
G
A
A
B
21
20
22
23
21
27
27
24
25
26
4
27
21
20
FOR 95R ELEVATION DISCOVER SI UNITS ONLY:
3.
Cable Routing
3a.
Carefully pull the COAXIAL CABLE from inside the CONSOLE BRACKET (15).
3b.
Install the coaxial extension coupler and coaxial extension cable.
3c.
Tape the ends of all CABLES
(Power, Coaxial, I-R Remote Control, Video)
together.
4. Feed the taped end of the MEDIA CABLES (12) through the large hole in the back of the CONSOLE BRACKET (15).
Carefully pull excess media cable through the CONSOLE BRACKET.
5
Slide one GROMMET (16) over the taped end of the MEDIA CABLES (12).
6. Hold the MAIN BRACKET ASSEMBLY (5) close to the CONSOLE BRACKET (15) as shown. With the holes facing
upward, feed the taped end of the MEDIA CABLES (12) through the bottom large hole of the main bracket
assembly and out of the upper hole as shown. Carefully pull excess media cable through the main bracket
assembly.
7. Slide the remaining GROMMET (16)
over the taped end of the MEDIA
CABLES (12). Install the grommets
into the access holes.
8. Install the MAIN BRACKET CAPS
(19) to the top and bottom of the
MAIN BRACKET ASSEMBLY (5).
9. Secure the MAIN BRACKET
ASSEMBLY (5) using four
SCREWS (17) and WASHERS (18)
as shown. Tighten the screws
securely. (8-10 ft. lbs.)
10.
Connect Cables to Console
10a.
Attach the three MEDIA CABLES
(12) to the back of the Discover SI
CONSOLE as shown.
Remote
High-Def
Power
Cross-Trainer & Bikes
Elevation Discover SI Console
95R ELEVATION DISCOVER INSPIRE UNITS ONLY
19
15
19
18
17
9
16
12
5
Summary of Contents for ATV15-XXXA-02
Page 1: ...1008767 0001 AA 15 ATTACHABLE TV ASSEMBLY INSTRUCTIONS ...
Page 2: ......
