LG VK9821 Series Owner'S Manual Download Page 18 | Manualshive

Page: 18 / 32

background image

18

How to use

Using the sani punch nozzle

Features

This nozzle is ideal for picking up dust through porous

surfaces such as thick blankets and mattresses, as a

result of the vibrating action of the sani punch nozzle.

The bottom part can be separated to be cleaned.

Since the bottom does not stick to the surface,

vacuuming is easy.

How to use

Follow the directions below for proper use.

Assembly

Connect the nozzle to the telescopic tube.

Sani punch nozzle

Set the suction power control switch to MAX POWER before vacuuming.

Depending on the type of surface handling may be awkward or it may

cause a lot of noise.

If this is the case, adjust the suction power control switch to the lower setting.

«
...
16
17
18
19
20
...
»

Summary of Contents for VK9821 Series

































Reviews:

No comments

Related manuals for VK9821 Series

Brand: RIDGID Pages: 36

Brand: UFESA Pages: 40

SANITAIRE H-2268

Brand: U-Line Pages: 3

PROFESSIONAL VJF608PF 0202

Brand: Vacmaster Pages: 55

Brand: COOLFORT Pages: 20

Brand: Kiwi Pages: 28

Brand: UFESA Pages: 36

Brand: Cleanfix Pages: 31

Brand: Dyson Pages: 10

Brand: Vax Pages: 12

Brand: Orion Pages: 6

Brand: Vaporetto Pages: 16

U-Smart Robot Vacuum

Brand: UMAX Technologies Pages: 28

Brand: Rainbow Pages: 8

TUFF SUCKER P710

Brand: Ryobi Pages: 16

Brand: Panasonic Pages: 12

Brand: DeWalt Pages: 100

Brand: DeWalt Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands