LG VK9821 Series Owner'S Manual Download Page 25 | Manualshive

Page: 25 / 32

background image

25

How to use

Cleaning air filter and motor safety filter

• Open the Vacuum cleaner cover by pushing the button.

• Grasp the handle of the dust separator and take it out.

• Open the guide cover by pulling the guide cover lever and remove dust.

• Open the pre filter cover by pulling the pre filter cover lever and take out

pre filter.

• Wash air filter and motor safety filter with water.

• Do not wash filters with hot water.

• Dry fully in shade so that moisture is entirely removed before reinstalling.

NOTE:

Never operate the vacuum with wet or damp filters.

NOTICE

If filters are damaged, do not use them.

In this case, contact LG Electronics Service

Agent.

Wash filters at least onec a month.

Pre-filter cover

Guide cover

Dust separator

Air filter

Motor safety filter

«
...
23
24
25
26
27
...
»

Summary of Contents for VK9821 Series

































Reviews:

No comments

Related manuals for VK9821 Series

POWERbot SR20J925 Series

Brand: Samsung Pages: 56

Brand: Lavor Pages: 39

Steam Station II

Brand: Haan Pages: 8

Brand: Maestro Pages: 104

Brand: YATO Pages: 64

Brand: Kärcher Pages: 28

Brand: Daewoo Pages: 38

Brand: Trisa Pages: 45

Brand: cecotec Pages: 141

Brand: Thomas Pages: 72

Brand: iRobot Pages: 24

Brand: Rowenta Pages: 3

Brand: POLTI Pages: 6

PlasmaWave WAC-5000

Brand: Winix Pages: 28

Brand: Zelmer Pages: 50

Brand: Daewoo Pages: 6

Flanders AstroPure 500-IR

Brand: AAF Pages: 21

Brand: Exido Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands