LG VK9821 Series Owner'S Manual Download Page 21 | Manualshive

Page: 21 / 32

background image

21

Follow the instruction below for through washing.

(Do not soak the entire body of the vacuum nozzle in water, it may cause the vibrator to malfunction)

1

2

3

4

5

6

➊

Press the button on the

rear side of the vacuum

nozzle to separate the

bottom plate.

➍

Straighten the punch bar

on the lower section.

➎

Insert the attachment

projections on bottom

plate to the vacuum

nozzle grooves.

➏

Push down the

tabs to secure.

➋

Wipe all the soiled parts

of the vacuum nozzle

body with a cloth.

➌

Wash the removed

bottom plate with water

and dry it.

Punch bar

Punch bar

Bottom plate

Bottom plate

«
...
19
20
21
22
23
...
»

Summary of Contents for VK9821 Series

































Reviews:

No comments

Related manuals for VK9821 Series

MCCG902 - CANISTER VACUUM - MULTI LANGUAGE

Brand: Panasonic Pages: 56

MCCG902 - CANISTER VACUUM - MULTI LANGUAGE

Brand: Panasonic Pages: 60

MCCG467 - CANISTER VAC - MULTI LANGUAGE

Brand: Panasonic Pages: 20

Brand: Kärcher Pages: 126

Brand: Kärcher Pages: 160

Brand: Kärcher Pages: 14

Brand: Kärcher Pages: 13

Brand: Kärcher Pages: 44

Brand: NuTone Pages: 60

Brand: Kogan Pages: 16

Brand: Numatic Pages: 16

TORNADO DELUXE HEPA VACUUM

Brand: U-Line Pages: 28

Brand: Yard force Pages: 26

Brand: DUSTER Pages: 8

Brand: V.Brøndum Pages: 20

Brand: Shark Pages: 16

Brand: V. BRØNDUM A/S Pages: 51

Brand: IRIT Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands