LG V-NET PQCPC22A0 Installation & User Manual Download Page 76

Page: 76 / 125

Installin

ACP

ENGLISH

Fixing the ACP to the wall

ACP can be installed by fixing to the wall. To install the ACP in an adequate place, proceed ac-

cording to the following explanation. It explains here on how to install the ACP with the example

of installing the ACP on the wall.

- Decide the space to install the ACP.

Before installing the ACP, check if it is the adequate place to connect the ACP with the power,

RS-485, and LAN cable.

- Fix to the wall using the driver. It can be fixed as in the following figure according to the loca-

tion to install.

PQCPC22A0

Connecting RS-485 cable to the ACP

After fixing the ACP in the installation place, RS-485 cable that was connected to PI485 shall be

connected to the ACP. To connect RS-485 cable to the ACP, proceed as the following order.

- First, among the connectors that can be connected to the ACP, connect the end of RS-485

cable connected to BUS-A of PI485 to Tx part. Next, connect the end of RS-485 cable con-

nected to BUS-B of PI485 to Rx part.

- RS-485 cable that was connected to PI485 shall be connected to CH port (RS-485 port) of the

ACP.

Plug the connector connecting RS-485 cable into one of CH1 ~ CH4 ports.

There are 1~6 CH ports, and it must be plugged into one of 1~4 ports for use.

PQCPC22A0

Summary of Contents for V-NET PQCPC22A0






























































































































Search results

Summary of Contents for V-NET PQCPC22A0

Reviews:

Brands by name

Popular brands

LG V-NET PQCPC22A0, Installation & User Manual

Search results

Summary of Contents for V-NET PQCPC22A0

Reviews:

Brands by name

Popular brands