8
READ ALL INSTRUCTIONS BEFORE USE
For your safety, the information in this manual must be followed to minimize the risk of
fire or explosion, electric shock, or to prevent property damage, injury to person, or death.
WARNING
SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY
To reduce the risk of fire, electric shock, or injury to persons when using this
appliance, follow basic precautions, including the following:
WARNING:
•
Do not, under any circumstances, cut or remove
the ground prong from the power cord.
To prevent
injury to person or damage to the dryer, the electrical
power cord must be plugged into a properly grounded
outlet.
•
For personal safety, this dryer must be properly
grounded.
Failure to do so can result in electric shock
or injury.
•
Refer to the installation instructions in this manual
for specific electrical requirements for your model.
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
•
This dryer must be plugged into a properly
grounded outlet. Electric shock can result if the
dryer is not properly grounded. Have the wall
outlet and circuit checked by a qualified electrician
to make sure the outlet is properly grounded.
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
•
The dryer should always be plugged into its own
individual electrical outlet which has a voltage
rating that matches the rating plate.
This provides
the best performance and also prevents overloading
house wiring circuits which could cause a fire hazard
from overheated wires.
•
Never unplug your dryer by pulling on the power
cord. Always grip plug firmly and pull straight out
from the outlet.
The power cord can be damaged,
resulting in a risk of fire and electric shock.
•
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
The power cord can
melt, creating electric shock and/or fire hazard.
•
When installing or moving the dryer, be careful not
to pinch, crush, or damage the power cord.
This will
prevent injury and prevent damage to the dryer from
fire and electric shock.
•
To reduce the risk of injury to person, adhere to all
industry recommended safety procedures
including the use of long sleeved gloves and safety
glasses.
Failure to follow all of the safety warnings in
this manual could result in property damage, injury to
person or death.
•
Connect the power cord to the terminal block. Each
colored wire should be connected to same color
screw. Wire color indicated on manual is
connected to the same color screw in block.
Failure
to follow these instructions may result in a short or
overload.
WARNING
ELECTRIC SHOCK HAZARD
Failure to follow safety warnings could result in serious injuly or death.
This dryer is equipped with a three-prong grounding plug to protection against shock hazard and
should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the
grounding prong from this plug.
SAVE THESE INSTRUCTIONS
Summary of Contents for GDL1329CED3
