LG AS-H246DGM0 Manual Download Page 47

Page: 47 / 56

- 47 -

LGE Internal Use Only

Troubleshooting Guide

Electronic Parts

Product does not operate at all.

(* Refer to Electronic Control Device drawing and Schematic diagram.)

Turn off Main Power

Turn on Main Power

Does "beeping" sound is made from the Indoor Unit?

Primarily, the operating condition of Micom is OK.

Check the voltage of power(About AC 220V, 60Hz)

(About AC 220/240V, 50Hz)

• Main power's voltage
• Voltage applied to the unit
• Connecting method of Indoor/Outdoor connecting

cable

• Check PWB Assembly

- Fuse
- Pattern damage
- Varistor(ZNR01J)

Check the connection housing for contacting

• Connector related to CN-NI, RY-COMP NO.3
• Connector related to CN-MOTOR
• Connector contacting of Outdoor Fan/Compressor
• Display PCB Assembly Check

Check each load(Indoor/Outdoor Fan Motor,
Compressor, Stepping Motor) and contacting
condition of related connector

Main PCB Board Operation Check

Items

• SMPS Transformer

(Indoor unit)
- Input Voltage
- Output Voltage(C03D)

• IC01D(7805) Output

(Indoor/Outdoor unit)

• IC01A(KIA7036, Reset IC)

OSC01B(8MHz)

• Replace Trans

• Replace IC01D

• Replace faulty parts

- About AC220V/240V±10% - Check the power voltage
- About DC12V

• DC +5V

• Voltage of IC No.1,

(DC +4.5V over) and Soldering condition.

Content

Remedy

YES

(After 10 seconds)

Summary of Contents for AS-H246DGM0
























































Search results

Summary of Contents for AS-H246DGM0

Reviews:

Related manuals for AS-H246DGM0

Brands by name

Popular brands

LG AS-H246DGM0, Manual

Search results

Summary of Contents for AS-H246DGM0

Reviews:

Related manuals for AS-H246DGM0

Brands by name

Popular brands