LG AS-H246DGM0 Manual Download Page 14

Page: 14 / 56

- 14 -

LGE Internal Use Only

Installation

The wall you select should be strong and solid
enough to prevent vibration

1. Mount the installation plate on the wall with four

type A screws. If mounting the unit on a concrete
wall, use anchor bolts.

• Mount the installation plate horizontally by aligning

the centerline using a level.

2. Measure the wall and mark the centerline. It is

also important to use caution concerning the
location of the installation plate-routing of the
wiring to power outlets is through the walls typi-
cally. Drilling the hole through the wall for pip-
ing connections must be done safely.

• Drill the piping hole with a ø70mm hole core drill.

Drill the piping hole at either the right or the left
with the hole slightly slanted to the outdoor side.

• Open the Front Grille.

• Pass Telephone Control Cord Wire through the hole

which the power cord goes through.

• Connect Telephone Control Cord Wire to the phone jack

of telephone PCB of Control Box.

• Fix Telephone Control Cord Wire inside Control box so

as not to disconnect.

• Close the Front Grille.

How to Fix Installation Plate

Drill a Hole in the Wall

Drain hose junction

• Remove the rubber stopple in the desired drain direc-

tion.

• Insert drain hose into the handle of drain pan, and join

drain hose and connecting hose according to the figure
by.

5-7mm

(3/16"~5/16")

Indoor

WALL

Outdoor

Connecting

part

Adhesive

Drain

hose

Only the
desired direction

Type "A" screw

Installation Plate

Installation plate

Left rear piping

Right rear piping

Chassis

Hook

SD(24k)

120

110

CHASSIS

(Grade)

Distance (mm)

Summary of Contents for AS-H246DGM0
























































Search results

Summary of Contents for AS-H246DGM0

Reviews:

Related manuals for AS-H246DGM0

Brands by name

Popular brands

LG AS-H246DGM0, Manual

Search results

Summary of Contents for AS-H246DGM0

Reviews:

Related manuals for AS-H246DGM0

Brands by name

Popular brands