LG AS-H246DGM0 Manual Download Page 48

Page: 48 / 56

- 48 -

LGE Internal Use Only

Troubleshooting Guide

The product is not operate with the remote controller.

Turn on Main Power

While the compressor has been stopped, the compressor does not

operate owing to the delaying function for 3 minutes after stopped.

Caused by other parts except the remote control

Cause by the remote control

When the mark( ) is displayed in LCD screen, replace
battery.

Check the contact of CN-DISP1 connector.

When the compressor stopped Indoor Fan is driven by a low speed.
At this point the wind speed is not controlled by the remote controller.
(When operated in the Sleeping Mode, the wind speed is set to the
low speed by force.)

Check Display PCB Assembly
- Voltage between CN DISP1

: DC +5V

Check the connecting circuit between the remote controller
MICOM (No. ) - R16(1.5k) - IR LED - TR - R17(1

Ω

MICOM (No.

) - R1(1.5k) - IR LED - TR - R2(1

Ω

Check point

• Check the connecting circuit between CN-DIS1

R11L(100

Ω

) - C01A(100nF) - MICOM PIN

• Check Receiver Assembly

Summary of Contents for AS-H246DGM0
























































Search results

Summary of Contents for AS-H246DGM0

Reviews:

Related manuals for AS-H246DGM0

Brands by name

Popular brands

LG AS-H246DGM0, Manual

Search results

Summary of Contents for AS-H246DGM0

Reviews:

Related manuals for AS-H246DGM0

Brands by name

Popular brands