LG 55EW960H Commercial Mode Setup Manual Download Page 67

Page: 67 / 89

206-4307

Reference: Updating TV/PTC Software using a USB Memory Device

(Cont.)

(Continued from previous page)

Select the file(s) to download, and then select UPDATE below.

Update TV Software

EW960H_CPU_SW.epk

Update PTC Software

EW960H_PTC_SW.txt

Import Clone File

EW960H_IM.tlx

USB DEVICE

TV MANAGER

Ez Download

USB 1:

Device Name

Ez Download

Update TV Software

Update PTC Software

Import Clone File

Diagnostics

UPDATE

Current TV Software Version:

version#

filename.epk/Version: version#

6. Use the Up/Down arrow keys to select

Update TV Software

Update PTC Software

, as

applicable, and press the Wheel (

) button.

Depending on your selection, a list of either TV or PTC software files stored in the LG_DTV

folder on the USB memory device will be displayed on the screen. Above the listing of files, you

can also see the current version of TV or PTC software. The following screen sample illustrates

an Update TV Software screen.

USB DEVICE

TV MANAGER

Update TV Software

USB 1:

Device Name

Ez Download

Update TV Software

Update PTC Software

Import Clone File

Diagnostics

UPDATE

Select the file to download, and then select UPDATE below.

Current TV Software Version:

version#

filename.epk/Version: version#

7. Use the arrow keys to select/highlight the update file to download, and then press the Wheel

(

) button.

8. When you are ready to download the update, select

UPDATE

on the screen, and then press

the Wheel (

) button on the Installer Remote.

Software update progress will be displayed on the screen. Do NOT remove the USB device until

the software update is complete. When the software update is complete, an UPDATE COMPLETE

pop-up banner will briefly be displayed at the bottom of the screen, and then, the TV will reboot.

Summary of Contents for 55EW960H


























































































Search results

Summary of Contents for 55EW960H

Reviews:

Related manuals for 55EW960H

Brands by name

Popular brands

LG 55EW960H, Commercial Mode Setup Manual

Search results

Summary of Contents for 55EW960H

Reviews:

Related manuals for 55EW960H

Brands by name

Popular brands