30
206-4340
Installer Menu (Cont.)
NOTE:
For items 007, 008, and 009
For legacy reasons, the scale used is 0 – 63. The PTC software
will translate this to the 0 – 100 scale used by the TV.
To translate a TV volume level to the Installer Menu value, use
the following formula:
Installer Value = TV Value x 63
100
Enter only the whole number (disregard fractions).
007 - STRT VOLUME (Start Volume)
This function allows the Installer to determine the initial volume
level setting when the TV is turned ON. This feature is useful for
an in-house information channel, since the TV will always select
that volume level when it is turned ON. The range of values is 0
to 63, 255. If set to 255, the last volume level before the TV was
turned OFF will be the current volume level when the TV is turned
ON again.
Note:
The factory default volume level (i.e., when AC power is
initially applied) for these TV models is 20. In addition, if AC power
is removed/disconnected and then reapplied to the TV while this
item is set to 255, the TV volume level will revert to 20 when the
TV is turned ON again.
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allowable
with the Volume (VOL) Up/Down control. In this way, for example,
someone cannot set the volume too low to hear. The value range
is from 0 to 63. The factory default is 0, which provides the full
range of volume control, if item 009 MAX VOLUME is set to 63. It
is recommended to set the same value on every TV.
Note:
The minimum volume level cannot have a value setting
higher than the maximum volume level (described below).
009 - MAX VOLUME (Maximum Volume)
This function determines the maximum volume level allowable
with the Volume (VOL) Up/Down control. In this way, for example,
someone cannot set the volume level high enough to disturb others.
The value range is 0 to 63, with 63 as the default, which gives the
user the full range of volume control, if item 008 MIN VOLUME is
set to 0. It is recommended to set the same value on every TV.
Note:
The maximum volume level cannot have a value setting
lower than the minimum volume level (described above).
010 - MUTE DISABLE
Enables or disables sound mute function. If set to 1, sound cannot
be muted. If set to 0, sound can be muted.
015 - SLEEP TIMER
If set to 1, the Sleep Timer feature is enabled and available to the
end user. Set to 0 to disable the Sleep Timer feature.
016 - EN. TIMER (Enable On/Off Timers)
If set to 1, the Timer function is enabled and available to the end
user. Set to 0 to disable On/Off timers.
Note:
The TV clock must be set in order for timers to be used.
017 - ALARM
If set to 1, the Alarm feature is enabled and available to the end
user in the Function Menu (i.e., the TV is not in Pass-through
Mode). Set to 0 to disable the Alarm feature.
Note:
The TV clock must be set before the Alarm feature will
work.
020 - FEATURE LEVEL
Determines an additional IR code scheme to which the TV will
respond, allowing for the use of unique IR codes based on “bed
number” in a multi-TV single room installation. First determine the
IR mode; then select the bed number.
Values
IR Mode
Bed #
0
Disabled
N/A
16 – 24
Multi-code Remote
1 – 9
Note:
For further information, see documentation for the accessory
package that includes the multi-code remote.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control) and have it available
to the end user to filter and control or otherwise restrict programming
content that can appear. Set to 0 to turn off the V-Chip feature (not
available to user); no programming restrictions can be set.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum number of Parental
Control blocking hours that can be set in the Function Menu (i.e.,
the TV is not in Pass-through Mode). Default setting is for 12
blocking hours.
Note:
This item is not available in the Installer Menu when item 021
V-CHIP is set to 0 or when item 084 PERMANENT BLK is set to 1.
023 - CAPTION LOCK
If set to 0, captions are off when the TV is turned ON. If set to 1,
the caption setting selected before the TV was turned OFF will be
the current caption setting when the TV is turned ON again.
028 - CH. OVERIDE (Channel Override)
This item either allows or restricts tuning of channels that are NOT
in the PTC Channel Map.
If set to 1, end users can tune channels
that are not in the PTC Channel Map by direct keypad entry. If
set to 0, users are restricted to only the channels that are in the
PTC Channel Map. In the case of CPU-CTV Mode, there are no
channels in the PTC Channel Map; therefore, direct keypad entry
is not available. Also, when this item is set to 0, the PTC Channel
