Lexmark T642 - Monochrome Laser Printer Manual Download Page 44

Page: 44 / 55

Understanding printer messages

Network <x>, <y>

A network interface is the active communication link, where <x>
represents the active communication link, and <y> represents the
channel.

No held jobs

Wait for the message to clear.

No jobs found

Note: The four-digit personal identification number (PIN) you entered is
not associated with any confidential print job.
• Select

Try again

to enter another PIN.

• Select

Cancel

to exit the

Enter PIN

screen.

No jobs to cancel

Wait for the message to clear.

No recognized file types

Wait for the message to clear.

Note: The only supported file type is PDF.

Overflow Bin Full

Remove the stack of paper from the bin to clear the message.

Parallel

A parallel interface is the active communication link.

Parallel <x>

Port disabled Remove USB drive

Wait for the message to clear.

Power Saver

• Send a job to print.
• Press

to warm the printer to normal operating temperature and

display the

Ready

message.

Printer locked, enter PIN to unlock

The operator panel has been locked.

Enter the correct PIN number.

Printing

Wait for the message to clear.

Printing Alignment Page

Wait for the message to clear.

Printing from USB drive
DO NOT REMOVE

Warning:

Do not turn the printer off or remove the USB drive while this

message is displayed.

Wait for the message to clear.

Printer busy

Continue

Quit

Press

to read the information from the USB drive.

Select

Quit

to cancel the information retrieval process.

Programming System Code

Warning:

Do not turn the printer off while this message is displayed.

Wait for the message to clear and the printer to reset.

Programming Flash

Warning:

Do not turn the printer off while this message is displayed.

Wait for the message to clear.

Programming Disk

Warning:

Do not turn the printer off while this message is displayed.

Wait for the message to clear.

Reading USB drive DO NOT REMOVE

Wait for the message to clear.

Ready

Send a job to print.

Reattach bin <x>

• Turn the printer off and back on.

– If the error recurs, turn the printer off, unplug the power cord from

the wall outlet, and remove the specified bin, then reattach the bin
to the printer, reconnect the power cord to a properly grounded
outlet, and then restart the printer.

– If the error recurs, turn the printer off, unplug the power cord from

the wall outlet, and remove the specified device, and call for service.

• Press

to clear the message and print without using the specified

bin.

Message

Action

Summary of Contents for T642 - Monochrome Laser Printer























































Search results

Summary of Contents for T642 - Monochrome Laser Printer

Reviews:

Related manuals for T642 - Monochrome Laser Printer

Brands by name

Popular brands

Lexmark T642 - Monochrome Laser Printer, Manual

Search results

Summary of Contents for T642 - Monochrome Laser Printer

Reviews:

Related manuals for T642 - Monochrome Laser Printer

Brands by name

Popular brands