Leviton evr-green Installation Manual Download Page 35 | Manualshive

Page: 35 / 50

background image

evr-green

™

Level

2 -

Network Charging Station For Public Applications

www.leviton.com/evrgreen • 1-877-338-7473 • [email protected]

Step 1 - Check box for correct contents

Holster and cable assembly

Evr-Green Networked Charging Station’s
holster and cable assembly ships in a box

(Evr-Green Part Number CTCLX-30 or

CTCNX-30) containing:

• bolts and washers (3)

• cable assembly with SAE J1772 Connector

• 5/32” allen wrench

• Locked Holster(CTCLX-30) or Unlocked

Holster(CTCNX-30)

WARNING

for CTCLX-30 with Locking

Holster. DO NOT place J1772 connector in

holster until head has been assembled and
the unit has been provisioned. Connector
will not remove from holster until station is
functioning and a user can be authorized.

Holster

Cable Assembly

5-2

«
...
33
34
35
36
37
...
»

Summary of Contents for evr-green



















































Reviews:

No comments

Related manuals for evr-green

Brand: oaniso Pages: 26

Brand: Targus Pages: 2

Brand: AccuPower Pages: 2

Brand: ANSMANN Pages: 32

MicroTalk FRS 104

Brand: Cobra Pages: 6

Brand: Analytic Systems Pages: 12

Brand: Toa Pages: 8

Brand: Jarv Pages: 8

Brand: XTline Pages: 45

Brand: Yeelight Pages: 33

POWER PEAK LIPOLY 300 EQ

Brand: ROBBE Pages: 28

Brand: Durst Pages: 2

Brand: YATO Pages: 64

Brand: PLUS START Pages: 8

Brand: CEMONT Pages: 60

Brand: Kobalt Pages: 28

IMPRES 2 PMPN4350

Brand: Motorola Pages: 168

IMPRES Smart Energy System

Brand: Motorola Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands