LevelOne WPS-1133 User Manual Download Page 24

Page: 24 / 84

5. Type in a Print Queue Names.

Note:

Each print queue corresponds to each print port of the print server.

6. Click

7. Done.

8. From your NetWare client computer, such as Windows 95/98/Me, create a printer that is

connected (redirected) to one of the NetWare print queues serviced by the print server.

Manual Setup

Manual Setup is a configuration program designed for more experienced users. Also, all the
configurations here can be configure by the WEB management of print server. You can refer
to the Chapter 5.

General

1. Select the print server that you wish to configure.
2. Click

Properties

in the tool bar and the following screen will appear,

Properties

button

just like a picture

＜

＞

, as follow picture.

Then, user can change the print server’s device name and password. Default is no

password.

Summary of Contents for WPS-1133





















































































Search results

Summary of Contents for WPS-1133

Reviews:

Related manuals for WPS-1133

Brands by name

Popular brands

LevelOne WPS-1133, User Manual

Search results

Summary of Contents for WPS-1133

Reviews:

Related manuals for WPS-1133

Brands by name

Popular brands