manualshive.com logo in svg

Lenovo ThinkCentre M800, Hardware Maintenance Manual, Page: 43 / 178

Share
Download
Lenovo ThinkCentre M800 Hardware Maintenance Manual Download Page 43

For detailed FRU information, such as the FRU part numbers and supported computer models, go to:
http:/www.lenovo.com/serviceparts-lookup

Parts on the system board

Note:

For the parts that are displayed on the following figure but not introduced in the following table, see

“Front view” on page 27 and “Rear view” on page 29.

Figure 5. Parts on the system board

1

PS/2 keyboard and mouse connector

2

4-pin power connector

3

Microprocessor

4

Microprocessor fan connector

5

Memory slot (DIMM1)

6

Memory slot (DIMM2)

7

Memory slot (DIMM3)

8

Memory slot (DIMM4)

9

Thermal sensor connector

10

10-pin power connector

11

Storage drive fan connector

12

SATA power connectors (2) (for connecting an optical

drive or a storage drive)

13

Front USB 3.0 connector

14

eSATA connector

15

Front fan connector

16

SATA 3.0 connectors (3)

17

Front panel connector

18

Front USB connector 2 (for connecting an additional

USB device)

19

Front USB connector 1 (for connecting an additional

USB device)

20

M.2 card slot (for installing a PCI adapter card)

21

Serial connector

22

Internal speaker connector

23

Front audio connector

24

PCI Express card slot (physical link width x16;

negotiable link width x4, x1)

Chapter 2

.

Product overview

35

Summary of Contents for ThinkCentre M800



















































































































































































Reviews:

No comments