manualshive.com logo in svg

Lenovo ThinkCentre M800, Hardware Maintenance Manual, Page: 141 / 178

Share
Download
Lenovo ThinkCentre M800 Hardware Maintenance Manual Download Page 141

Replacing the rear Wi-Fi antenna

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

To replace the rear Wi-Fi antenna, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 88.

3. Straighten the rear Wi-Fi antenna so that it can be more easily twisted.

4. Hold the thicker end of the rear Wi-Fi antenna and unscrew the Wi-Fi antenna from the rear of the

computer.

Figure 90. Removing the rear Wi-Fi antenna

5. Install the new rear Wi-Fi antenna to the rear Wi-Fi antenna cable connector attached on the rear of

the computer. Then, adjust the angle of the rear antenna to reduce the risk of breaking the antenna
by accident.

Figure 91. Removing the rear Wi-Fi antenna

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 147.

Chapter 9

.

Installing or replacing hardware

133

Summary of Contents for ThinkCentre M800



















































































































































































Reviews:

No comments