Lenovo ThinkCentre M800 Hardware Maintenance Manual Download Page 134

Page: 134 / 178

4. Locate the PCI adapter card. The PCI adapter card is installed in the M.2 card slot on the system board.

See “Parts on the system board” on page 35.

5. Remove the three screws that secure the PCI adapter card to the system board. Then, slide the adapter

card as shown to remove it from the system board.

Figure 76. Removing the PCI adapter card

6. Slide the new PCI adapter card into the M.2 card slot on the system board until it snaps into position.

Then, install the three screws to secure the new PCI adapter card to the system board.

Figure 77. Installing the PCI adapter card

7. Install the PCI card. See “Replacing the PCI card” on page 124.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 147.

Replacing the Wi-Fi card

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

126

ThinkCentre M800 and M900 Hardware Maintenance Manual

Summary of Contents for ThinkCentre M800


















































































































































































Search results

Summary of Contents for ThinkCentre M800

Reviews:

Lenovo ThinkCentre M800, Hardware Maintenance Manual, Page: 134 / 178

Search results

Summary of Contents for ThinkCentre M800

Reviews: