manualshive.com logo in svg

Lenovo ThinkCentre M800, Hardware Maintenance Manual, Page: 130 / 178

Share
Download
Lenovo ThinkCentre M800 Hardware Maintenance Manual Download Page 130

9. Open the retaining clips and gently pull the memory module out of the memory slot.

Figure 69. Removing a memory module

10. Position the new memory module over the appropriate memory slot. Ensure that the notch

1

on the

memory module aligns correctly with the slot key

2

on the system board. Push the memory module

straight down into the slot until the retaining clips close.

Figure 70. Installing a memory module

11. Reinstall the PCI Express x16 graphics card if you have removed it. See “Replacing a PCI Express

card” on page 134.

12. Position the heat sink fan duct on the top of the new heat sink and fan assembly as shown. Then, press

the heat sink fan duct straight down until it snaps into position.

122

ThinkCentre M800 and M900 Hardware Maintenance Manual

Summary of Contents for ThinkCentre M800



















































































































































































Reviews:

No comments