manualshive.com logo in svg

Lenovo ThinkCentre M800, Hardware Maintenance Manual, Page: 143 / 178

Share
Download
Lenovo ThinkCentre M800 Hardware Maintenance Manual Download Page 143

• If the card is held in place by a retaining latch, press the card retaining latch

1

as shown to disengage

the latch. Grasp the card and gently pull it out of the slot.

6. Install the new PCI Express card into the appropriate PCI Express card slot on the system board.

See “Parts on the system board” on page 35.

Note:

If you are installing a PCI Express x16 graphics card, ensure that the memory slot retaining clips

are closed before you install the graphics card.

Figure 94. Installing a PCI Express card

7. Pivot the card latch to the closed position to secure the PCI Express card.

Figure 95. Securing the PCI Express card

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 147.

Chapter 9

.

Installing or replacing hardware

135

Summary of Contents for ThinkCentre M800



















































































































































































Reviews:

No comments