Lenovo 10K9 Hardware Maintenance Manual Download Page 124

Page: 124 / 158

7. Pivot the card latch to the closed position to secure the PCI/PCI-Express card.

Figure 41. Installing a PCI/PCI-Express card

8. Reinstall the screw to secure the PCI Express card latch in place.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 126.

Replacing the Wi-Fi card

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

To replace the Wi-Fi card, do the following:

1. Remove any media from the drives and turn off all connected devices and the computer. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.

2. Remove the computer cover. See “Removing the computer cover” on page 90.

3. Locate the Wi-Fi card. See “Computer components” on page 31.

4. If your computer comes with a Wi-Fi card that supports the Bluetooth function, disconnect the Bluetooth

cable from the Wi-Fi card adapter.

Note:

The Bluetooth cable connects the Bluetooth connector on the Wi-Fi card adapter to the system

board.

5. At the rear of the computer, remove the screw that secures the card latch.

6. Grasp the Wi-Fi card adapter that is currently installed and gently pull it out of the slot.

116

ThinkCentre M73p Hardware Maintenance Manual

Summary of Contents for 10K9






























































































































































Search results

Summary of Contents for 10K9

Reviews:

Lenovo 10K9, Hardware Maintenance Manual, Page: 124 / 158

Search results

Summary of Contents for 10K9

Reviews: