Leister Comet 500 Operating Manual Download Page 15

Page: 15 / 44

Status LED (26) for the

Drive on/

off key (25)

Condition

Cause

LED off

Heating is switched off.

LED lights up green

Drive is switched on

If, during operation of the drive, a warning message occurs in the

Status display area 2 (31)

or if there is an

error message in the

working display (29),

then this will be displayed as followed:

LED flashes red

Drive power limit is active

see Warning and error messages

COMET 700 [10]

LED lights up red

The drive has an error

see Warning and error messages

COMET 700 [10]

The

Status LED (26)

on the

Drive on/off (25)

displays the drive state.

Drive

7.3. Display of the status LED

Status LED (26) for the

Heating

on/off key (24)

Condition

Cause

LED off

Heating is switched off.

LED flashes green

Heating is switched on, hot wedge

temperature outside the tolerance

range

LED lights up green

Heating is switched on, hot wedge

temperature within the tolerance

range

If, during operation, a warning message occurs in the

Status display area 2 (31)

or if there is an error mes-

sage in the

Working display (29),

then this will be displayed as followed:

LED flashes red

Warning message for the heating

see Warning and error messages

COMET 700 [10]

LED lights up red

Error message for the heating

see Warning and error messages

COMET 700 [10]

The

Status LED (26)

on the

Heating on/off (24)

key displays the respective heating state.

Heating

Summary of Contents for Comet 500













































Search results

Summary of Contents for Comet 500

Reviews:

Related manuals for Comet 500

Brands by name

Popular brands

Leister Comet 500, Operating Manual

Search results

Summary of Contents for Comet 500

Reviews:

Related manuals for Comet 500

Brands by name

Popular brands