background image

REQUIRED TOOLS

WARNING

: Use tools with caution and follow all 

necessary safety protocols.

AVERTISSEMENT

: Utiliser des outils avec prudence 

et suivre tous les protocoles de sécurité nécessaires. 

Your FlexView Conferencing Cart includes a Vaddio® HuddleSHOT FC (Flush-Mounted Camera) and 

may include the FlexView Conferencing Cart Front Shelf option, a Cat 6,Cable Retractor Option, and/or 

a Power Cable Retractor Option, if ordered.

NOTE

• Only proceed to installing any options you may have purchased and/or using your HuddleSHOT FC    

  after first completing the steps in this instruction sheet to completely install your FlexView Conferencing  

 Cart.

• Please take the time to carefully unpack and inspect all of the products you ordered, gather    

 

  the corresponding printed instructions and save them for future use.

• If any printed instructions are missing, please report it immediately to Technical Support at    

 

  [email protected] or (866) 977-3901.

The printed instructions for your FlexView Conferencing Cart with HuddleSHOT FC and any options 

purchased should include the following:

• The FlexView Conferencing Cart with HuddleSHOT FC (FVS-HSFC-800SC-WH) Instruction Sheet    

 (100-00057)

• The FlexView Conferencing Cart Front Shelf Option (FVS-HS-FRTSHLF-WH) Instruction Sheet  

 

 (100-00058)

• The FlexView Conferencing Cart Cat 6 (FVS-800-CAT6-20F) and Power (FVS-800-RET15F) Cable   

  Retractor Options Instruction Sheet (100-00059)

• The FlexView Conferencing Cart with HuddleSHOT FC Getting Started Guide (411-0037-02)

• Maintenance and care information is provided in Care and Cleaning of Products (I-00788) and

  Unpacking and Handling Precautions (I-00787) for your convenience.

Page 6

SUPPLIED COMPONENTS AND HARDWARE (CONTINUED)

NOTE

• To order more hardware, contact support at    

  [email protected] or (866) 977-3901.

• Additional hardware is included that may not be  

  required for your installation.

• Protective Eyewear

• Power Driver

• #2 Phillips    

 

 Screwdriver

• #2 Phillips Bit

• Toothpick or 

  Small Straw

• ½” Socket

• 5/16” Socket

• 7/16” Socket

• Adjustable Wrench

EMEA Power Cable Option

NOTE

: An optional EMEA power cable kit includes 

EU1-16P and UK1-13P cables (shown top to bottom).

Power Cable

(NEMA5-15P)

R

(20x)

#6 Washer 

For Mounting

Small-Screw 

Components

to Lever Lock 

K

(8x)

8-32 

Pan Head 

Screw 

N

(3x)

Plastic

Lever Lock

Locking Rivet

J

(2x)

Key

P

(12x)

Wire Tie

L

(8x)

Cable 

Management 

Clip

M

INTRODUCTION

Summary of Contents for MIDDLE ATLANTIC FlexView Series

















Reviews: