background image

HANGING YOUR DISPLAY ONTO THE HORIZONTAL MOUNTING BRACKET

Page 14

1. With at least one other person, carefully lift your  

 

    display slightly above both top and bottom rails on the  

    horizontal mounting bracket. (

FIGURE S

)

2. 

Slowly lower the display while ensuring hooks on the  

    top and bottom of both interface brackets fully engage  

    onto the horizontal mounting bracket.

WARNING: 

Do not release your display until 

certain the top hook of each interface bracket is 

securely seated on the upper rail of the horizontal 

mounting bracket.

AVERTISSEMENT:

 Ne relâchez pas votre 

écran tant que le crochet supérieur de chaque 

support d'interface n'est pas fermement installé 

sur le rail supérieur du support de montage 

horizontal.

WARNING: 

This procedure requires at least one additional person.

AVERTISSEMENT:

 Cette procédure nécessite au moins une personne supplémentaire.

3. Check for proper height.

NOTE

• Achieving your desired height may require    

  repositioning the horizontal mounting bracket   

  and/or removal and reinstallation of interface   

  brackets (F).

• Adjust torque on power driver to lightest setting  

  and only increase as necessary.

4. Use a power driver, #2 Phillips bit, 

    (2x) 10-32 x ¾” locking screws (G), and 

    (2x) 10-32 flange nuts (H) to secure the  

 

    interface brackets (F) to your cart as shown.   

   (

FIGURE T

)

Side of Horizontal 

Mounting Bracket 

Hooks on 

Interface 

Brackets

FIGURE S

FIGURE T

F

G

H

Horizontal 

Mounting

Bracket 

Summary of Contents for MIDDLE ATLANTIC FlexView Series

















Reviews: