28/29
Technical data sheet: S000114123EN-1
Updated:
Created: 18/01/2021
Cat. No(s): 0 026 72/73/74/76/78/79
KNX controller multi-application DIN
7 . COMMUNICATION OBJECTS (continued)
7 .15 Blind Object Description
No
Object name
Name
DTP Type
Length Flags
95
Move blind/shutter up-down
Output A
DPT 1.008
1 bit
CW
When the telegram is received from bus, blind is moved to the direction (the value 0 or 1) of
movement of the set time.
The object is;
0 = up
1 = down
96
Slat adjustment/stop up-down
Output A
DPT 1.007
1 bit
CW
While blind is moving, the telegram is received then the blind movement is stopped. Other
time the blind slat can be adjusted.
The object is;
0 = stop/slat move one step open
1 = stop/slat move one step close
97
Blind/shutters up-down limid
Enable limitation
Output A
Output A/B
DPT 1.008
DPT 1.003
1 bit
CW
This communication objects are controlled by “Limit travelling range” parameter. Blind up or
down end position can be limited by this communication object. The blind stops automatically
when the configured upper or lower end position have been reached. After the bus voltage,
return object value is set to 0 so this meaning upper end position is limited.
For the first communication object “Blind/shutters up-down limit”;
0 = limited upper end position active
1 = limited lower end position active
For the second communication objet “Output A/B, Enable limitation”
0 = limitation disable
1 = limitation enable
98
Move to position height 0…255
Output A
DPT 5.001
1 byte
CW
If device is received this telegram, the blind is moved to height determined by the percentage
of value. After the blind moving operation is finished, the slats are returned its previous
position.
While the blind is moving, the “Move slat 0…255” command is received from the bus. If the
blind is reached its target position, the slats are set to the received position.
The object is;
0
= upper end position %0
…
255
= lower end position %100
99
Move slats 0…255
Output A
DPT 5.001
1 byte
CW
If the device is received this communication object, the slats are moved to the desired position.
The object is;
0 = slats open %0
…
255 = slat closed %100
100
101
Move to position 1, 2
Move to position 3, 4
Output A
DPT 1.022
1 bit
CW
This object is used to move to the blind saved preset position. After the position has been
reached, the slat position is move to the own preset position.
The object is;
0 = move to position 1 or 3
1 = move to position 2 or 4
102
103
Set position 1, 2
Set position 3, 4
Output A
DPT 1.022
1 bit
CW
This object is used to save the current position of blind. If the telegram value is received 0, the
current position is stored as the new position 1 or 3. If the telegram value is received 1, the
current position is stored as the new position 2 or 4.
The object is ;
0 = set to position 1 or 3
1 = set to position 2 or 4
104
Trigger reference movement
Output A
DTP 1.008
1 bit
CW
This object is triggered the reference movement. If the telegram is received, the blind is moved
up or down end position. Then the blind can return its last position or desired position. End of
reference movement, the device is updated travel times.
The travel time operation can be interrupted by
• Weather alarm, forced operation, block functio
• Manual operation
• Move to position UP or DOWN commands
The object is;
0 = no reaction
1 = trigger the reference movement (UP – DOWN – UP)
105
Block
Output A
DPT 1.003
1 bit
CWTU
The state of the blind cannot changed by other control commands as long as block telegram
with the value 1 is received. You can define the reaction of output relay via parameters.
The object is;
0 = operation enable
1 = operation disable
7 . COMMUNICATION OBJECTS (continued)
7 .15 Blind Object Description (continued)
No
Object name
Name
DTP Type
Length Flags
106
Forced operation 1 bit
Output A
DPT 1.003
1 bit
CWTU
If the telegram is received (value 1), the blind is moved to parameterized position and the blind
is locked for the movement command. After the forced operation is disabled by the object
(value 0), the blind is moved to parameterized position.
The object is:
0 = operation enable
1 = forced active / operation disable
106
Forced operation 2 bit
Output A
DPT 2.002
2 bit
CWTU
If the telegram is received value 2 or value 3, the blind is moved to UP (2) or DOWN (3) and
the blind is locked for the movement command. After the forced operation is disabled by the
object (value 0) or (value 1), the blind is moved to parameterized position.
The object is:
0 = operation enable
1 = operation enable
2 = forced active, move UP / operation disable
3 = forced active, move DOWN / operation disable
107
Status height 0…255
Output A
DPT 5.001
1 byte
CRT
The blind position of drive is available as a value 0…255 percentage %0…%100. The height
status is to be transmitted or read out via this object.
The height status object is only updated when the blind has reached a target position after
movement.
The object is:
0 = upper end position %0
…
255 = lower end position %100
108
Status slat 0…255
Output A
DPT 5.001
1 byte
CRT
The blind slat position of drive is available as a value 0…255 percentage %0…%100. The slat
status is to be transmitted or read out via this object.
The slat status object is only updated when the blind has reached a target position after
movement.
NOTE:
This object is only available in the venetian blind type.
The object is:
0 = slat open %0
…
255 = slat close %100
109
Status upper end position
Output A
DPT 1.011
1 bit
CRT
The blind is reached the upper end position, the device sends information.
The object is:
0 = the blind is not in upper end position
1 = the blind is in upper end position
110
Status lower end position
Output A
DPT 1.011
1 bit
CRT
The blind is reached the lower end position, the device sends information.
The object is;
0 = the blind is not in lower end position
1 = the blind is in lower end position
CONTENTS
