12/29
Technical data sheet: S000114123EN-1
Updated:
Created: 18/01/2021
Cat. No(s): 0 026 72/73/74/76/78/79
KNX controller multi-application DIN
7 . COMMUNICATION OBJECTS (continued)
7 .5 "Enable Input a…s" parameter (continued)
7 .5 .3 "a - Blind Sensor" parameter (continued)
Operating functionality of the blind
* 1 push-button, short=stepping,
long=moving
1 push-button, short=moving,
long=stepping
1 push-button-operation, moving
1 switch-operation, moving
2 push-button, standard
2 switch-operation, moving
2 push-button, moving
2 push-button, stepping
•
1 switch operation, moving
Start of operation
This property is for moving only shutters up or
down.
While button is pressing, operation is
continuing. This action is opposite direction to
the last movement for moving the shutter up or
down.
End of operation
When button releases, operation stop.
Stop/ Lamella adj. command is send than
movement stopped.
With below functions, you must set the parameters for a second
key (second input) with the corresponding settings for the shutter
movement in the opposite direction.
•
2 button, standard
Short operation
Stop / lamella adjustment
The stop/lamella adjustment object is
adjustment of the lamella UP or DOWN. In
additional it stops a running movement of the
shutter.
Long operation
This action is for moving the chosen direction
shutter. Movement direction is choosing on
parameter move up or moves down.
•
2 switch operation, moving(shutter)
Start of operation
This property is for moving only shutters up or
down.
While button is pressing, operation is
continuing. This action is moving the shutter
“
move up
” or “
move down
”.
End of operation
When button releases, operation stop.
“
Stop/ Lamella adj . UP
” or “
Stop/ Lamella
adj . DOWN
” command is send than movement
stopped.
You should use the property with two switches.
•
2 switch operation, moving(shutter)
On operation
The property object “Shutter” is choose and
performs the up‐ and down‐movement of the
shutter.
The direction of movement depends to the
parameters. When the button pressed firstly,
than shutter move in direction that it was
programmed. Second time button is pressed
shutter stop command is sent such as STOP/
Lamella adj. UP or STOP/Lamella adj. DOWN.
1) Shutter MOVE UP
STOP/Lamella UP
2) Shutter MOVE DOWN
STOP/Lamella DOWN
•
2 button, stepping
On operation
Stop / lamella adjustment
The stop/lamella adjustment object is
adjustment of the lamella UP or DOWN. Lamella
move direction chooses on the parameters.
7 . COMMUNICATION OBJECTS (continued)
7 .5 "Enable Input a…s" parameter (continued)
7 .5 .3 "a - Blind Sensor" parameter (continued)
Connected contact type
normally closed
*normally open
The contact type of the push button attached to the channel is
adjusted here.
Reaction on short operation
*STOP/lamella UP
STOP/lamella DOWN
This parameter is visible if there is distinction between short and long
operation.
Stop/step lamella adjustment parameter. This parameter object stops
shutter movement.
Reaction on long operation
MOVE UP
*MOVE DOWN
Distinction between short and long:
This parameter use for choose shutter movement direction.
Long operation after
0,3s…
*0,4s
…10s
Distinction between short and long:
Long press time period is select here.
Telegr . STOP/lamella adj . is repeated every
0,3sn…
*0,4s
…10sn
Only visible 1 push-button, short=moving,
This parameter we choose each sending stop/lamella telegram-
sending period. Lamella adjustment cyclically.
Debounce time
10ms…
*50ms
…150ms
Debounce uses the input, which means checking twice in a short
period of time to make sure it’s definitely pressed.
7 .5 .4 "a - Value/Forced Operation" parameter
You can use these value/forced functions to parameterize different
object actions. You can transmit one or two objects short or long press
status sequence, and select the size of the objects required (1 bit, 2-bit
priority control, 1 byte, 2 byte or 4 byte) as needed. This enables you to
parameterize a large number of application options. You can enter two
values and set whether and how they are to be transmitted short or
long.
Connected contact type
normally closed
*normally open
The contact type of the push button attached to the channel is
adjusted here.
Distinction between long and short
operation
yes
*no
If the parameter is set no, the input will be evaluated normally on
every edge of the input signal.
Yes is selected. There is a delay after opening/closing the contact to
determine whether there is a short or long operation.
CONTENTS
