Leadshine MX4660 Hardware Installation Manual Download Page 7

Page: 7 / 28

Hardware

installation manual of the multi-axis drive MX4660

Leadshine Technology Co., Ltd

Leadshine America, Inc.

Page 7/28

3/F, Block 2, Nanyou Tianan Industrial Park, Shenzhen, China

25 Mauchly, Suite 318, Irvine, CA 92618, USA

Tel: 86-755-26409254

Fax: 86-755-26402718

Tel: 1-949-608-7270

Fax: 1-949-608-7298

Web:

www.leadshine.com

Email:

[email protected]

Web:

www.leadshine.com

Email:

[email protected]

Dimensions

Unit: mm (1 inch = 25.4 mm)

Figure 2 MX4660 dimensions

Get Started

Before you start hardware connection, refer to the following MX4660 layout diagram (figure 3) for
connector/DIP switch location. Read the MX4660 datasheet for each connector explanation. Then, get the
following prepared:



A 24-54 VDC power supply.



Up to 4 stepper motors depending on how many axes that MX4660 will power in your application.



A source of step signals, such as a motion controller, PLC, or a PC-based control system (Mach 3, EMC, etc.).



A small flat blade screw driver for tightening the screw connectors of the MX4660.



Whatever optional external devices needed to be controlled through the built-in outputs and inputs.

Figure 3

MX4660 layout

CN1: DB25 Connector

CN5:Z-Axis Motor Connector

CN3:X-Axis Motor Connector

CN4:Y-Axis Motor Connector

CN9:Analog Output

CN8:Digital Outputs (6 DO)

CN2:Power Connector (4pin)

CN10:

26-pin Low Profile

Header for I/O expansion (4DI/4DO)

CN6:A-Axis Motor Connector

CN7:Digital Inputs (8DI)

Summary of Contents for MX4660





























Search results

Summary of Contents for MX4660

Reviews:

Related manuals for MX4660

Brands by name

Popular brands

Leadshine MX4660, Hardware Installation Manual

Search results

Summary of Contents for MX4660

Reviews:

Related manuals for MX4660

Brands by name

Popular brands