LAUNCH TECH X-431 PRO3 User Manual Download Page 16

Page: 16 / 97

LAUNCH

X-431 PRO3 V4.0 User Manual

Connectivity

Wi-Fi (802.11a/b/g/n/ac)

Bluetooth

Working temperature

℃

~ 50

℃

Storage temperature

-20 ~

℃

1.4.2 VCI device (Only for Passenger Vehicle Configuration)

Working voltage

9 ~18V

Working temperature

℃

~ 50

℃

Relative humidity

20% ~ 90%

1.4.2 VCI module (Only for Commercial Vehicle/ Gasoline & Diesel
Configuration)

Working voltage

DC 9 ~36V

Power consumption

≤

Communication

Via Bluetooth/Wi-Fi or USB connection

Working temperature

℃

~ 50

℃

1.5 Package List (Only for Passenger Vehicle Configuration)

Common accessories are same, but for different destinations, the accessories
(such as diagnostic software, testing connectors) may vary. Please consult from
the local agency or check the package list supplied with this tool together.

No.

Item

Descriptions

Qt.

Display tablet

Indicates the test result.

VCI connector

Collects the vehicle data and sends it
to the tablet for analysis.

Summary of Contents for X-431 PRO3


































































































Search results

Summary of Contents for X-431 PRO3

Reviews:

Related manuals for X-431 PRO3

Brands by name

Popular brands

LAUNCH TECH X-431 PRO3, User Manual

Search results

Summary of Contents for X-431 PRO3

Reviews:

Related manuals for X-431 PRO3

Brands by name

Popular brands