LAUNCH TECH X-431 PRO3 User Manual Download Page 32

Page: 32 / 97

LAUNCH

X-431 PRO3 V4.0 User Manual

Follow the steps mentioned below to connect OBD II vehicle:

1. Locate vehicle’s DLC socket.
2. Plug the VCI device into the vehicle’s DLC socket (It is suggested to use the

OBD II extension cable to connect the VCI device and DLC socket).

3. Choose one of the two ways to obtain power from:

A. Power adaptor: Connect one end of the included power adaptor to

charging port of the tablet, and the other end to AC outlet.

B. Internal battery pack

For non-OBDII vehicle, proceed as follows:

1. Locate vehicle’s DLC socket.
2. Select the corresponding non-16pin connector.

3. Plug the non-16pin end of the connector into the DLC socket, then connect

the other end to the OBD I adaptor, and then tighten the captive screws.

4. Connect the other end of the adaptor to the included VCI device.

5. If the pin of the DLC is damaged or has insufficient power, please follow the

either of the following methods to proceed:

A. Cigarette Lighter cable (optional): Connect one end of the cigarette lighter
cable to vehicle’s cigarette lighter receptacle, and the other end to the power
jack of OBD I adaptor.

B. Battery Clamps Cable: Connect one end of the battery clamps cable to
vehicle’s battery, and the other end to the power jack of OBD I adaptor.

Summary of Contents for X-431 PRO3


































































































Search results

Summary of Contents for X-431 PRO3

Reviews:

Related manuals for X-431 PRO3

Brands by name

Popular brands

LAUNCH TECH X-431 PRO3, User Manual

Search results

Summary of Contents for X-431 PRO3

Reviews:

Related manuals for X-431 PRO3

Brands by name

Popular brands