LAUNCH TECH X-431 PRO3 User Manual Download Page 48

Page: 48 / 97

LAUNCH

X-431 PRO3 V4.0 User Manual

This function is used to read the version information of system mode, vehicle
VIN, software and ECU.

B. Read Fault Code

This function displays the detailed information of DTC records retrieved from the
vehicle’s control system.

*Note: Retrieving and using DTCs for troubleshooting vehicle operation is only one

part of an overall diagnostic strategy. Never replace a part based only on the DTC

definition. Each DTC has a set of testing procedures, instructions and flow charts that

must be followed to confirm the location of the problem. This information can be found

in the vehicle’s service manual.

On the diagnostic function selection screen, tap “Read Fault Code”, the screen
will display the diagnostic result.

On-screen Buttons:

Freeze Frame:

When an emission-related fault occurs, certain vehicle

conditions are recorded by the on-board computer. This information is referred

Summary of Contents for X-431 PRO3


































































































Search results

Summary of Contents for X-431 PRO3

Reviews:

Related manuals for X-431 PRO3

Brands by name

Popular brands

LAUNCH TECH X-431 PRO3, User Manual

Search results

Summary of Contents for X-431 PRO3

Reviews:

Related manuals for X-431 PRO3

Brands by name

Popular brands