Lars Thrane Iridium Certus 200 User & Installation Manual Download Page 9

Page: 9 / 141

LT-4200 User & Installation Manual Rev. 1.00

Introduction

Lars Thrane A/S

www.thrane.eu

vii

Table of Contents

Introduction

...................................................................................................................................................... 1

Application and Limitations

.............................................................................................................................. 2

Unpacking (in-the-box)

..................................................................................................................................... 3

Inspection

...................................................................................................................................................... 3

Accessories

........................................................................................................................................................ 4

Mounts

.......................................................................................................................................................... 4

Cable and connectors

................................................................................................................................... 4

System Overview

.............................................................................................................................................. 5

Installation and Mounting

................................................................................................................................ 6

LT-4210 Control Unit

..................................................................................................................................... 6

LT-3120 Handset

........................................................................................................................................... 9

LT-3121 Cradle

............................................................................................................................................. 10

LT-4230 Antenna Unit

................................................................................................................................. 11

Pole Mount (2.0” pipe, Ø53.0mm, A4 Stainless), Antenna Unit

............................................................... 19

Interfaces

......................................................................................................................................................... 22

LT-4210 Control Unit

................................................................................................................................... 22

LT-4230 Antenna Unit

................................................................................................................................. 30

Power Consumption

....................................................................................................................................... 32

Maximum

.................................................................................................................................................... 32

DC Isolation Resistance and Chassis Ground

................................................................................................. 33

Galvanic Isolated Power Supply

..................................................................................................................... 35

AC/DC Galvanic Isolated Power Supply

..................................................................................................... 35

DC/DC Galvanic Isolated Power Supply

..................................................................................................... 35

User Interface (UI)

........................................................................................................................................... 36

Display

......................................................................................................................................................... 37

Menu System

.............................................................................................................................................. 41

Activating the System

..................................................................................................................................... 43

Acquire a Certus SIM Card

.......................................................................................................................... 43

Postpaid Voice Features

............................................................................................................................. 43

Who’s My Service Provider

........................................................................................................................ 44

Change of Hardware and Software

................................................................................................................ 45

Change of Hardware

................................................................................................................................... 45

Software Update

......................................................................................................................................... 46

Summary of Contents for Iridium Certus 200














































































































































Search results

Summary of Contents for Iridium Certus 200

Reviews:

Related manuals for Iridium Certus 200

Brands by name

Popular brands

Lars Thrane Iridium Certus 200, User & Installation Manual

Search results

Summary of Contents for Iridium Certus 200

Reviews:

Related manuals for Iridium Certus 200

Brands by name

Popular brands