Lars Thrane Iridium Certus 200 User & Installation Manual Download Page 59

Page: 59 / 141

LT-4200 User & Installation Manual Rev. 1.00

System Services

Lars Thrane A/S

www.thrane.eu

Page 48 of 128

External SIP Phones

The LT-4200 system supports connection of up to 8 external SIP phones. The configuration of the SIP
phones must be completed via the web server, see

Telephony

on page 95. Figure 44 is illustrating the

connection of the external SIP phones. Connect the SIP phones directly to the LT-4210 Control Unit
Ethernet (LAN port) or through an Ethernet switch.

NOTE

The SIP phone might require a DHCP Server to get an IP address assigned. Depending on
network setup, it might be needed to configure DHCP Server mode in the LT-4200 system.

The LT-4210 Control Unit UI display (MENU -> System -

> SIP Phones) will provide a ‘live’ registration status

of the SIP phones configured from the web server.

An active voice call to/from a SIP phone is not shown on the Control Unit on Certus, see Figure 46.

Figure 44: SIP phones

Figure 45: System Submenu (SIP Phones)

Figure 46: External SIP Voice Call

SIP Phones:
MENU -> System -> SIP
Phones

External SIP voice call is
not shown on the LT-
4210 Idle screen.

Summary of Contents for Iridium Certus 200














































































































































Search results

Summary of Contents for Iridium Certus 200

Reviews:

Related manuals for Iridium Certus 200

Brands by name

Popular brands

Lars Thrane Iridium Certus 200, User & Installation Manual

Search results

Summary of Contents for Iridium Certus 200

Reviews:

Related manuals for Iridium Certus 200

Brands by name

Popular brands