Lars Thrane Iridium Certus 200 User & Installation Manual Download Page 17

Page: 17 / 141

LT-4200 User & Installation Manual Rev. 1.00

Installation and Mounting

Lars Thrane A/S

www.thrane.eu

Page 6 of 128

Installation and Mounting

LT-4210 Control Unit

The LT-4210 Control Unit is the master unit in the system, supporting all external interfaces and the
operational user interface. The LT-4210 Control Unit is designed for indoor mounting. Check the
specifications in

App. G - Specifications

on page 120.

The LT-4210 Control Unit has the following interfaces:

•

pin power connector (male), marked ‘PWR’

•

Chassis ground connector, marked ‘GNDC’

•

N connector (female) for coaxial cable to the LT-4230

Antenna Unit, marked ‘ANT’

•

Ethernet (RJ-

45) connector, marked ‘LAN’

•

10-

pin auxiliary connector (male), marked ‘AUX’

•

SIM card, marked ‘SIM’

•

5-pin connector (female) for LT-3120 Handset (front of the control unit)

The interfaces on the back side of the LT-4210 Control Unit are illustrated in Figure 3 on page 7.

Figure 2: LT-4210 Control Unit (front view).

Summary of Contents for Iridium Certus 200














































































































































Search results

Summary of Contents for Iridium Certus 200

Reviews:

Related manuals for Iridium Certus 200

Brands by name

Popular brands

Lars Thrane Iridium Certus 200, User & Installation Manual

Search results

Summary of Contents for Iridium Certus 200

Reviews:

Related manuals for Iridium Certus 200

Brands by name

Popular brands