Lars Thrane Iridium Certus 200 User & Installation Manual Download Page 24

Page: 24 / 141

LT-4200 User & Installation Manual Rev. 1.00

Installation and Mounting

Lars Thrane A/S

www.thrane.eu

Page 13 of 128

The LT-4230 Antenna Unit has a hazard warning label attached to the radome as illustrated in Figure 12.

WARNING

The safety distance from the LT-4230 Antenna Unit, is 0.4 m (1.3 ft), in order to comply
with the regional regulations.

IMPORTANT

: Due to the adjacency of the Iridium and Inmarsat frequency bands, the LT-4230 Antenna

Unit may not co-operate in the proximity of an active Inmarsat antenna unit, see

Coexisting

with Inmarsat L-band

on page 18.

Figure 12: LT-4230 Antenna Unit (incl. warning label)

Summary of Contents for Iridium Certus 200














































































































































Search results

Summary of Contents for Iridium Certus 200

Reviews:

Related manuals for Iridium Certus 200

Brands by name

Popular brands

Lars Thrane Iridium Certus 200, User & Installation Manual

Search results

Summary of Contents for Iridium Certus 200

Reviews:

Related manuals for Iridium Certus 200

Brands by name

Popular brands