Lantronix Open-Q 410 User Manual Download Page 38

Page: 38 / 38

5: Output Display Options

Open-Q 410 Dev Kit User Guide

Option 2: 4.5” panel manufactured by OSD Displays, with an integrated capacitive touch panel. Detailed

specifications of this display board:

•

Model No: OSD045T2906-43TS

•

Resolution: FWVGA (480x854xRGB)

•

Display Controller: Fitipower Integrated Technology JD9161BA

Support DSI Version 1.1

Support D-PHY version 1.00

•

Touch Controller: GoodixSilited GSL968 Multi Touch Capacitive

•

Interface: MIPI DSI (2 data lanes)

5.2 HDMI Output Adapter

The optional HDMI output adapter board can be used in place of the on-board display. The image below

shows the HDMI output adapter installed on the development kit.
There is a standard HDMI 1.4 Type A connector on a top left corner of the carrier board after the HDMI output

adapter installed.

Figure 21 – HDMI Output Adapter

Summary of Contents for Open-Q 410







































Search results

Summary of Contents for Open-Q 410

Reviews:

Related manuals for Open-Q 410

Brands by name

Popular brands

Lantronix Open-Q 410, User Manual

Search results

Summary of Contents for Open-Q 410

Reviews:

Related manuals for Open-Q 410

Brands by name

Popular brands