Lantronix Open-Q 410 User Manual Download Page 6

Page: 6 / 38

Open-Q 410 Dev Kit User Guide

1 Introduction

This user guide includes information needed for users to become familiar with the Open-Q™ 410 Development

Kit based on the Qualcomm® APQ8016E processor. The document includes:

•

Block Diagrams

•

Configuration Options

•

System on Module (SOM) hardware features

•

Carrier Board hardware features

•

Optional Accessories

For background information on the kit, go to:

https://www.lantronix.com/products/open-q-410-development-kit/

1.1 Intended Audience

This document is intended for end users who have purchased an Open-Q

410 Development Kit from the

Lantronix web store:

http://shop.intrinsyc.com/collections/qualcomm

1.2 Applicable Documents

Reference

Title

A-1

Intrinsyc Purchase and Software License Agreement for the Open-Q

410

Development Kit

1.3 Reference Documents

Reference

Title

R-1

Open- Q

410 Development Kit Display Board Design Guide Tech Note

R-2

Open- Q

410 Development Kit Camera Board Design Guide Tech Note

R-3

Open- Q

410 Development Kit Carrier Board Design Guide Tech Note

R-4

Open- Q

410 SOM Development Kit HW Revision Guide

Summary of Contents for Open-Q 410







































Search results

Summary of Contents for Open-Q 410

Reviews:

Related manuals for Open-Q 410

Brands by name

Popular brands

Lantronix Open-Q 410, User Manual

Search results

Summary of Contents for Open-Q 410

Reviews:

Related manuals for Open-Q 410

Brands by name

Popular brands